Descripción
Registros
Los datos en este recurso de registros biológicos han sido publicados como Archivo Darwin Core(DwC-A), el cual es un formato estándar para compartir datos de biodiversidad como un conjunto de una o más tablas de datos. La tabla de datos del core contiene 91 registros.
Este IPT archiva los datos y, por lo tanto, sirve como repositorio de datos. Los datos y los metadatos del recurso están disponibles para su descarga en la sección descargas. La tabla versiones enumera otras versiones del recurso que se han puesto a disposición del público y permite seguir los cambios realizados en el recurso a lo largo del tiempo.
Versiones
La siguiente tabla muestra sólo las versiones publicadas del recurso que son de acceso público.
Derechos
Los usuarios deben respetar los siguientes derechos de uso:
El publicador y propietario de los derechos de este trabajo es The University Centre in Svalbard. Esta obra está bajo una licencia Creative Commons de Atribución/Reconocimiento (CC-BY 4.0).
Registro GBIF
Este recurso ha sido registrado en GBIF con el siguiente UUID: 41ec671b-f43d-43d2-8605-5e5ef620cc4e. The University Centre in Svalbard publica este recurso y está registrado en GBIF como un publicador de datos avalado por GBIF Norway.
Palabras clave
Occurrence; Observation
Contactos
- Originador
- Originador
- Originador
- Punto De Contacto
- Punto De Contacto
Datos del proyecto
No hay descripción disponible
| Título | UNIS AB-202 |
|---|---|
| Identificador | https://www.wikidata.org/wiki/Q118395664 |
Personas asociadas al proyecto:
Métodos de muestreo
On the boat Teisten, nets were hitched to a crane by a hook at the opening of the net and slowly lowered at 0,4 m/s, to not tangle the net. When the net had reached desired depth, it was again slowly hoisted at 0,5 m/s as to allow water time to pass through the small mesh and allow for collection of animals. While the net came out of the water it was sprayed with salt water to collect all the animals in the bottom of the net, where a container is attached. This container has a filter on one of its side surfaces that lets excess water out while retaining the animals caught inside. At the bottom of this container is a valve that allows for emptying of the contents. This is transferred into buckets, labeled with their location and mesh size. Measurements were taken between 15:10 to 16:49 (local time) as that was when the driver had set aside time to operate the boat. Day one / 09.04.2026: Teisten went out to S1 and used WP2 180µm and WP3 to collect biomass, microzooplankton and a community analysis. Average bottom depth was 61,2 as the boat was moved by waves, most samples were taken from 50 m depth. Day two/ 10.04.2026: Teisten went out to KB3 and used WP3 for collection of microzooplankton. Bottom depth was 350m and samples were done at 340 and 330 m. On the way back Polarsyssel was used to collect samples at KB3 using the WP2 180µm mesh. Bottom depth was at 350 and net was lowered to 300.
| Área de Estudio | Sampling location: Ny Ålesund, Kongsfjorden KB3 is a long term sampling station located in Kongsfjorden (78.95403 °N, 11.95853 °E) Station 1 is a sampling station located in Kongsfjorden (78.93639 °N, 11.91966 °E) Teisten (boat) was used 09.04.2026 - 10.04.2026 for taking samples at KB3 and Station 1. Polarsyssel (boat) was used on 14.04.2026 for sampling at KB3. |
|---|
Descripción de la metodología paso a paso:
- On the boat Teisten, nets were hitched to a crane by a hook at the opening of the net and slowly lowered at 0,4 m/s, to not tangle the net. When the net had reached desired depth, it was again slowly hoisted at 0,5 m/s as to allow water time to pass through the small mesh and allow for collection of animals. While the net came out of the water it was sprayed with salt water to collect all the animals in the bottom of the net, where a container is attached. This container has a filter on one of its side surfaces that lets excess water out while retaining the animals caught inside. At the bottom of this container is a valve that allows for emptying of the contents. This is transferred into buckets, labeled with their location and mesh size. Measurements were taken between 15:10 to 16:49 (local time) as that was when the driver had set aside time to operate the boat. Day one / 09.04.2026: Teisten went out to S1 and used WP2 180µm and WP3 to collect biomass, microzooplankton and a community analysis. Average bottom depth was 61,2 as the boat was moved by waves, most samples were taken from 50 m depth. Day two/ 10.04.2026: Teisten went out to KB3 and used WP3 for collection of microzooplankton. Bottom depth was 350m and samples were done at 340 and 330 m. On the way back Polarsyssel was used to collect samples at KB3 using the WP2 180µm mesh. Bottom depth was at 350 and net was lowered to 300.
Metadatos adicionales
| Identificadores alternativos | https://ipt.gbif.no/resource?r=unis-ab202-2026-zooplankton |
|---|